Books about Sleeving from Amazon.com

Gives the requirements for non-heat-shrinkable sleeving, extruded from compounds based on polychloroprene elastomer. Sleeving of this type is normally available with internal diameters up to 25 mm. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in the application and not based on the specification alone..
Price: $46.00 [Notify me when price goes down.]

This standard gives the requirements for two types of heat-shrinkable, flame retarded, fluid resistant, nominal shrink ratio 2:1, fluoroelastomer sleeving for use at temperatures up to 200 C: - Type A: thick wall; Type B: thin wall. These sleevings are normally supplied with internal diameters up to 51 mm, and the standard colour is black. This title may contain less than 24 pages of technical content..
Price: $68.00 [Notify me when price goes down.]

Gives the requirements for non-heat shrinkable sleeving, extruded from compounds based on a blend of polyvinyl chloride and acrylonitrile elastomers. Sleeving of this type is normally available with internal diameter up to 25 mm, and in the following opaque colours: black, brown, red, orange, yellow, green, blue, violet, grey, white, pink and green/yellow. This title may contain less than 24 pages of technical content..
Price: $40.00 [Notify me when price goes down.]

Gives the requirements for three types of E-type glass sleeving using either braided or knitted construction with a continuous acrylic based coating, and differentiated by their breakdown voltage: high breakdown voltage (sheet 403), medium breakdown voltage (sheet 404) and low breakdown voltage (sheet 405). These sleevings have been found suitable for use at temperatures up to 155 �C. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone..
Price: $52.00 [Notify me when price goes down.]

Gives the requirements for three types of sleeving constructed from polyethylene terephthalate yarns using either braided or knitted construction, with a continuous acrylic based coating and differentiated by their breakdown voltage: high breakdown voltage (sheet 420), medium breakdown voltage (sheet 421) and low breakdown voltage (sheet 422). Experience of product performance indicates that sleeving of the types specified in these sheets may be suitable for operation at 130 �C or in some applications at temperatures up to 155 �C..
Price: $46.00 [Notify me when price goes down.]

Gives the requirements for four types of heat-shrinkable, flame- retarded, limited-fire-hazard sleeving with a thermal endurance rating of 105 �C as shown below: Class A: thin wall, shrink ratio 2:1, internal diameter up to 102,0 mm Class B: medium wall, shrink ratio 2:1, internal diameter up to 60,0 mm Class C: thick wall, shrink ratio 2:1, internal diameter up to 51,0 mm Class D: medium wall, shrink ratio 3:1, internal diameter up to 40,0 mm Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone..
Price: $74.00 [Notify me when price goes down.]

Gives the requirements for one type of heat-shrinkable, flame retarded, with a nominal shrink ratio 2:1, fluid resistant polyvinylidene fluoride sleeving for use at temperatures up to 175 C. This sleeving is normally supplied with an internal diameter up to 25,4 mm, and the standard colour is transparent. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the property requirements listed in Tables 2, 3, 4 and 5, with the exception of dimensions and mass. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This edition includes the following significant technical change with regard to the previous edition: Replacement of the thermal endurance test method according to IEC 60216 with a long term ageing test, i.e. 3 000 h at the recommended maximum temperature found suitable for use,in order to provide safe thermal test data within a workable time scale..
Price: $52.00 [Notify me when price goes down.]